First operational deployments take the 386-tonne transport combination from sea level to 500 (800) meters on the Swedish border.
Norwegian heavy haulage specialist CN Heavy Transport AS put its new SCHEUERLE STB 260 into service immediately after delivery, deploying the side girder bridge on two demanding transformer transports. The transformers, weighing 128 and 185 tons respectively, were transported over a distance of approximately 70 kilometers from the port of Bogen to Bjørnfjell on the Norwegian-Swedish border. During both projects, the new side girder bridge demonstrated its capabilities under challenging topographical conditions while highlighting the benefits of its outstanding payload-to-deadweight ratio.
One of the most capable side girder bridges in Scandinavia
For the first operational assignments of the new STB 260, CN Heavy transported two power transformers destined for an energy infrastructure project from northern Norway to Sweden. The transformers were manufactured by Italian manufacturer Tamini and transported from Italy to Norway via road and sea as part of an international logistics chain. CN Heavy was responsible for the final leg of the journey from the port of Bogen to the destination in Bjørnfjell on the Swedish border.
The heavier of the two transformers weighed 185 tons and measured approximately 9 meters in length, 3,2 meters in width and 4,65 meters in height. Combined with the side girder bridge, trailer units and prime movers, the complete transport combination reached a gross vehicle weight of 386 tons and an overall length of 71.5 meters.
“The STB 260 further expands our heavy haulage capabilities and opens up new opportunities for heavy transformer and infrastructure transports. Particularly impressive was the journey from sea level to an altitude of around 500 meters, including gradients of up to ten percent, the negotiation of traffic islands and extremely tight tunnel clearances. The bridge has clearly demonstrated its capabilities,” says Ole Kristian Ruud, Project Manager at CN Heavy Transport AS.
From sea level to 500 meters above sea level
The approximately 70-kilometre route ran from the port of Bogen to Bjørnfjell near the Swedish border. Once commissioned, the transformers will support key energy infrastructure in the region, including the railway connection between Narvik and Kiruna and further power transmission links between Norway and Sweden.
To reach their destination, the transport combination had to climb from sea level to an altitude of around 500 meters. The route followed sections of the E10 and E6 highways, passing through multiple tunnels and tackling gradients of up to 10 percent. Tight roundabouts, varying road profiles and the demanding terrain of northern Norway placed considerable demands on the drivers, transport planning and equipment alike.
One of the greatest challenges was the passage through the Leirvik Tunnel. At its narrowest point, the transport combination had just 5 centimeters of clearance to the tunnel roof. The maneuver therefore required exceptional precision and continuous monitoring by the escort team throughout the passage.
SCHEUERLE STB 260: high payload capacity with low deadweight for existing fleets
Despite a deadweight of only around 40 tons, it is capable of carrying loads of up to 260 tons, resulting in an exceptionally favorable payload-to-deadweight ratio. Prior to delivery, the STB 260 was also successfully tested beyond its rated payload capacity as part of an extensive overload testing program. This enables operators to transport heavy transformers with comparatively compact axle configurations. During the two inaugural transports in Norway, a configuration of 2 × 12 axle lines was used to move loads weighing up to 185 tons.
Another key feature of the new side girder bridge is its extensive compatibility. It can be combined not only with SCHEUERLE K25 modular platform trailers but also, as demonstrated by CN Heavy, with existing NICOLAS modular platform trailers. This allows operators to benefit from the latest side girder bridge technology without replacing their existing equipment.
In addition, the STB 260 offers a lifting range of 1,500 millimeters, various girder configurations for different load heights and an integrated roll stabilization system.
Successful market entry in Scandinavia
The successful completion of these first transports also marked the operational debut of the new STB 260 in CN Heavy Transport AS’s fleet. With the side girder bridge now in service, the company has gained a solution capable of handling demanding heavy haulage projects for the energy and infrastructure sectors safely and efficiently under the challenging operating conditions of northern Europe.
Company profile
The TII Group, a company owned by the Heilbronn-based Otto Rettenmaier family, is a globally active manufacturer of heavy-duty and special vehicles and has a workforce of around 1000 employees. The Group includes industry specialists, TII SCHEUERLE and TII KAMAG, and has production sites in Germany and India along with a worldwide organisation of sales and service partners. With innovative vehicles for manoeuvring and transportation operations, the TII Group, which is listed in the index of world market leaders, supports its customers in the transport and logistics sectors, building industry, plant engineering, air and space travel, shipbuilding, energy, steel and mining as well as yard logistics for realising a wide range of complex transport tasks. The TII Group holds the current world record of over 23,000 tonnes for the transportation of extremely heavy loads on vehicles. TII stands for the tradition of innovation, customer orientation and partnership as well as for high product quality and sustainability in heavy-duty mobility. www.tii-group.com
Partener Principal
MATEK Build Smart